Parts & Accessories

- Aluminum alloy shells resist corrosion and provide lightweight longevity - Sealed cartridge bearings offer smooth operation while resisting contaminants - 20mm Thru Axle with 15mm option, 6 bolt disc compatible

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

You know that feeling when you're just rippin' along and you hear the dreaded psssssssssssss sound from your tire? Well have no fear the TCS Tire Plug kit is here. It's easy to use and will get you back on two wheels in no time. More time for miles of smiles, rather than expletives on the side of the road or trail. Yea, we have all been there. The TCS Tire Plug Kit uses durable "Rocket" anchors (because they look like tiny rockets) that stay in your tire and hold the plug in place. You will not lose a plug. The anchor will hold it in place like a ship at dock. But wait... there's more... You can reuse the anchors when you're all done. It's like a treasure chest when you need to swap-out your tires. The Rocket Plug Kit also features an 'Extra Hand' tool under the smaller cap. If you haven't pre-loaded the Rocket, the Extra Hand will temporarily plug the hole and take the pressure off while you prepare your Rockets and plugs. We went through a lot of arguments at WTB to get this thing dialed and man, we are so stoked on how it turned out. We hope you like it as much as we do. REUSABLE "ROCKET" ANCHORS Rocket anchors rotate once pushed into the tire and physically prevent the plug from pulling back through the tire when running higher pressure or through heavy cornering like traditional plugs can. Oh, we tried to pull it through, and we were holding up e-bikes from the plug. The anchor remains fixed in place until it’s removed from the inside of the tire and put back in the tool for future use. Reusable and Recyclable! Win, win! EXTRA HAND The Extra Hand (because who couldn't use an extra hand every once and a while) stopper can be pushed into the puncture to temporarily stop any loss of air while a rider determines how many tire plugs are needed and prepares to seal it. The Extra Hand can also be used as a reamer to create a more uniform hole for the tire plugs to seal. COMPACT AND LIGHT The TCS Rocket Tire Plug Kit is CNC’d from 6061 aluminum alloy with an integrated extra hand tool and plunger. It also has internal storage for four anchors (two large and two small included), and fifteen 1.5mm diameter tire plugs. Ready to Launch Rocket anchors can be preloaded with 1-4 tire plugs depending on the terrain and size of punctures riders typically encounter. Preloaded Rocket anchors are then placed on the plunger, ready to launch the moment a puncture occurs. The clock is ticking! TCS Tubeless TCS (Tubeless Compatible System) is WTB's standardized tubeless system. When you do get a puncture with a tubeless tire with sealant inside, this is a great way to fix it.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - This axle is compatible with bikes that have a Cervelo R.A.T. thru-axle in the fork with 100 x 12mm front hubs. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Tubeless setup should be a "set it and forget it" affair. SPANK's tubeless valves are constructed of durable brass material and a tapered round rubber base which fits a wide range of rim designs. The extra-long shafts accommodate even the deepest well rims and most troublesome of pumps. Sealed removable valve cores for sealant injection make set up or topping up a breeze. - Material: Brass shaft, rubber plug - Weight (g): ±18/set - Length (mm): 40 shaft (55 total length) - Features: 2 pcs per set, removable valve core for sealant injection

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Be free—No longer are you constrained by the proprietary Focus R.A.T. axle. Simply replace the R.A.T. nut with our threaded nut and thru axle. A complete solution for a standard threaded axle for your R.A.T.-equipped bike. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

- Converts a 120mm OL spacing track hub to 130mm OL Road spacing 10mm nutted steel axle

- Longer skewers fit modern frames/forks with thicker dropouts - Aluminum lever/nut, Delrin pivot washer, serrated alloy nut with Nylock - White skewers are powder-coated - Shaft: chromoly - Wheel: front/rear - Spacing (front/rear): 100/135mm - Weight: 112g/set

- 10mm axle holes for mountain bike applications - 14mm axle holes for BMX applications - Heavy duty steel protects frame, tensions chain - M8 threading, Nylock nut

- Rear axle conversions for Spin Doctor Pro rear hub - Various replacement axles and conversion kits for Spin Doctor and Spin Doctor Pro hubs - Some conversions utilize pre-existing axle components for retrofit - Conversion kits for original Spin Doctor and Spin Doctor Pro hubs are not compatible with Spin Doctor 6-Drive hubs

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

Replacement clear plastic spoke guard.

• Locking skewer set • Cro-Mo • 70g (set)

- End caps for Origin8 FB-1100 fat bike hubs

- Axle adapters for CX/GX/MT/FB-1110 Elite Series front hubs - Available in standard QR, 12mm, 15mm, and 20mm thru-axle options - Material: Aly - Color: Blk

Replacement Cassette body for Origin8 hubs

Replacement cassette bodies for Origin8 RD-1200 series rear hubs - Supplier Part: QA1R - Use: Shi 11s - Bearing Type: Sealed - Compatibility: RD-1200

- End cap for Origin8 MT-3200 hubs - Spacing / Axle: 148mm

From Origin8 come these replacement hollow track axle sets for SS-1101 hubs.

- End cap adapters for Origin8 RD1120 series 11-speed road hubs

- End cap for Origin8 FB-1100 fat bike hubs

Replacement axle sets for use with Origin8 FB-2000 hubs Front Axle: - 3/8 x 26 x 135 x 175 Rear Axle: - 3/8 x 26 x 170 x 210

- Axle adapters for RD-1110 Elite Series front road disc hubs - Available in standard QR, 12mm, and 15mm thru-axle options

- Aluminum alloy shells resist corrosion and provide lightweight longevity - Sealed cartridge bearings offer smooth operation while resisting contaminents - 15mm Thru Axle, 6 bolt disc compatible in boost and standard configurations

- Axle adapters for RD-1110 Elite Series rear road disc hubs - Available in standard QR and 12mm thru-axle options - Axles included with adapters

Replacement axle sets for Origin8 RD-1200 series hubs - Front axle - Supplier Part: QA1F - Size: M9x100x108 - Spacing / Axle: QR - Material: Alloy - Thread Pitch: M9 - OLD: 100 - Length: 108

Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place